Skip to main content
Key Stuck In The Lock And Won't Turn Or Come Out

Key Stuck In The Lock And Won't Turn Or Come Out

The key has gone in but will not turn, or has turned part way and will not come back out, with the key still whole.

Caution · Fixed by a locksmith

Updated

What's happening?

A key that is stuck whole in the lock is a different fault from one that has snapped. The key is intact, but something inside the cylinder or the mechanism it drives is holding it: worn pins gripping the wrong depth, a cam that has slipped on the tailpiece, a bolt jammed hard against the frame, or a multipoint mechanism that has failed halfway through its travel. On a euro cylinder the key often stops at 45 degrees because the cylinder will only release the key in the straight position. On a uPVC or composite door the usual culprit is the locking mechanism, not the cylinder. The wrong response is force: a key that is pulled, levered or hammered is the key that snaps, and then the job is an extraction as well as a repair.

What usually causes it?

  • A worn key, or a copy of a copy, that no longer matches the cylinder pins
  • A euro cylinder that has failed internally and will not release the key in a turned position
  • A multipoint locking mechanism that has jammed part way through its throw
  • A door that has dropped so the bolt is jammed against the keep and loading the key
  • A night latch cylinder with the snib or deadlock set wrongly
  • Grit, paint or old lubricant packing the pins and the keyway

Is it dangerous?

Not physically, but a key stuck in a lock that is part way turned can leave you locked in or locked out, and a final exit door that will not open from the inside is a fire escape problem. Forcing the key risks it breaking in the barrel.

Can I fix it myself?

1. Stop pulling. Ease the key back to the position it went in, which is usually straight up, and try drawing it out gently. 2. If the key is held at an angle, wiggle it very lightly while keeping slight pressure towards the straight position. 3. Check that the snib or deadlock button is not set the wrong way on a night latch. 4. Do not use a hammer or pliers on the key. 5. Do not squirt glue-like sealants into the keyway. If it has not freed in a few minutes, call a locksmith.

When should you call a locksmith?

Call a locksmith if the key has not eased out after a few gentle attempts, if the door is locked with the key inside, if a uPVC door handle has stopped moving, or if the stuck door is the only way out of the house. Say the key is stuck, not broken: the fix is different.

What will the locksmith actually do?

  • Free the key without damaging the cylinder, usually by removing the cylinder from the door edge
  • Test the cylinder and the key against each other for wear
  • Replace a failed euro cylinder or night latch cylinder with a correctly sized one
  • Replace or free a uPVC or composite multipoint mechanism that has jammed
  • Cut a fresh key from the cylinder code rather than a worn copy

Who fixes this

Questions people ask

Can a stuck key be freed without replacing the lock?

Often yes. On many doors the cylinder can be unscrewed and removed with the key still in it, and the cylinder replaced. Whether the lock itself needs replacing depends on why the key stuck.

Why is my key stuck at a half turn?

Because the cylinder has failed or the mechanism it drives has jammed. The Master Locksmiths Association says the cause on a uPVC or composite door is most often the locking mechanism rather than the key.

Should I use lubricant to free a stuck key?

A tiny amount of dry lubricant will not hurt, but oil on a worn cylinder only collects grit, and lubricant will not fix a failed mechanism. If the key will not move after a gentle try, stop and call someone.

Sources & References

  1. Master Locksmiths Association: Key won't turn in lock, why this happens
  2. Master Locksmiths Association: Door lock types guide
  3. Master Locksmiths Association: uPVC door security

Need a locksmith?

Describe the job and get a fixed price from a local locksmith.