Skip to main content
Shaver Socket Not Working

Shaver Socket Not Working

A shaver point that has gone dead is either on a circuit that has tripped or has a failed supply unit, and because it sits in the bathroom the repair belongs to a registered electrician.

Low risk · Fixed by an electrician

Updated

What's happening?

A bathroom shaver socket is not an ordinary socket. Sockets are not allowed in bathrooms or shower rooms apart from shaver-supply units, unless they sit at least 2.5 metres from the edge of the bath or shower tray, and a shaver point within that distance has to be SELV or conform to BS EN IEC 61558-2-5. That is why the unit looks different, often in a mirror light or a small wall box beside the basin, and why it can fail without anything else in the house being wrong. When it goes dead, the usual suspects are the circuit feeding it, which may be a lighting circuit, and the unit itself. Because every circuit in or passing through a bathroom must be RCD protected, a trip elsewhere on that RCD can take the shaver point with it.

What usually causes it?

  • The circuit or RCD that feeds the shaver unit has tripped, and the unit has no supply
  • The shaver unit is supplied from the lighting circuit, so a dead light and a dead shaver point share a cause
  • The shaver-supply unit itself has failed, because it is a sealed isolating-transformer socket made to BS EN IEC 61558-2-5
  • A loose connection at the unit or at the junction box that feeds it
  • A mirror light or cabinet with a built-in shaver socket whose own fuse or switch has operated
  • A shaver or charger fault that trips the supply as soon as it is plugged in

Is it dangerous?

A dead shaver socket is not dangerous in itself, but bathrooms are among the highest-risk rooms for shock because wet skin reduces the body's resistance. Do not swap in an ordinary socket, use an extension lead to run a shaver from another room, or open the unit with wet hands. Unplug the shaver and leave the socket alone until it has been tested.

Can I fix it myself?

1. Check the consumer unit for a tripped RCD, RCBO or breaker and reset it once. 2. Try the bathroom light: if it is dead too, the fault is on that circuit rather than the shaver unit. 3. Plug the shaver into the unit with dry hands: if it trips the supply every time, try the shaver in a different shaver point or charge it elsewhere. 4. If the unit has a switch or a small fuse marked on the front or in a mirror light, check it is on. 5. If it is still dead or trips again, leave it and book an electrician. Do not remove the unit from the wall.

When should you call an electrician?

Call an electrician if the shaver socket stays dead after one reset, if the circuit trips again, if the unit is cracked, discoloured or has been wet, or if the light on the same circuit also fails. Replacing a shaver-supply unit is bathroom electrical work, which Electrical Safety First says must generally comply with Part P of the Building Regulations, so use a registered electrician.

What will the electrician actually do?

  • Isolate the circuit and test where the supply stops, at the consumer unit, the junction box or the unit
  • Check the circuit's RCD protection, because all circuits in or passing through a bathroom need it
  • Replace a failed shaver-supply unit with one made to BS EN IEC 61558-2-5, or an SELV supply
  • Re-terminate any loose or heat-damaged connections at the unit and the feeding junction box
  • Test the circuit and give the paperwork that bathroom work requires

Who fixes this

What it usually costs

Socket Installation Cost
£125–£450 for two double sockets

Questions people ask

Can I put a normal socket in my bathroom instead?

No. Sockets are not allowed in bathrooms or shower rooms apart from shaver-supply units, unless they can be fitted at least 2.5 metres from the edge of a bath or shower tray.

Why is my shaver socket dead but the bathroom light works?

The two may be on different circuits, or the shaver unit may have failed or lost a connection. An electrician can test where the supply stops.

Can I charge my shaver from the socket in another room?

Yes, if the shaver and its adaptor are used as the maker says. Electrical Safety First says to charge a shaver only with the adaptor supplied and to keep it unplugged when not in use.

Does replacing a shaver socket need a certificate?

Bathroom work is covered by Part P of the Building Regulations, and Electrical Safety First says to use a registered electrician for any electrical installation work in a bathroom.

Sources & References

  1. Electrical Safety First: bathroom safety
  2. Electrical Safety First: shavers
  3. GOV.UK: Approved Document P, electrical safety in dwellings

Need an electrician?

Describe the job and get a fixed price from a local electrician.