Skip to main content
Light Bulbs Keep Blowing

Light Bulbs Keep Blowing

A bulb that fails again and again is usually telling you the lamp does not suit the fitting, the dimmer or the heat in the fitting, and a scorched holder means stop and get it checked.

Caution · Fixed by an electrician

Updated

What's happening?

A bulb that dies within weeks, or the same fitting eating bulbs one after another, is a pattern worth chasing rather than a run of bad luck. In most homes the cause is a mismatch: a lamp rated above the fitting's maximum wattage, a cool beam (dichroic) lamp in a downlight made only for aluminium reflector lamps, or an LED lamp that is not made for the dimmer it sits on. Heat plays a part too, because downlights covered by loft insulation cannot shed it. The lampholder itself can be the culprit: a holder that has overheated, scorched or corroded stops making a clean contact, and each new bulb then fails the same way. The pattern across the house tells you where to look. One fitting points to that fitting, one room points to that room's circuit, and every room points to a wider supply or lamp-quality question.

What usually causes it?

  • A lamp with a higher wattage than the fitting's marked maximum, which overheats the lamp and the holder
  • A cool beam (dichroic) reflector lamp fitted in a downlight designed only for aluminium reflector lamps
  • An LED lamp that is not marked as dimmable running on a dimmer switch
  • A lampholder that is damaged, scorched, corroded or discoloured, so contact is poor and heat builds up
  • Downlights covered by loft insulation or combustible material that are not rated for it, so heat cannot escape
  • A replacement lamp much heavier than the one it replaced, which can loosen contact and retention in some holders

Is it dangerous?

A single failed bulb is harmless. Repeated failures in one fitting with a scorched, discoloured or corroded holder are not: Electrical Safety First says not to fit a new lamp into a damaged, scorched or corroded holder, and to replace faulty or overheating fittings promptly. Heat damage in a downlight is a recognised fire risk, so treat brown marks, curled labels or a melted holder as a stop sign.

Can I fix it myself?

1. Switch the light off at the switch and the circuit off at the consumer unit before touching the lamp. 2. Read the maximum wattage and lamp type marked on the fitting and on the bulb packaging, and fit only a matching lamp. 3. If the fitting is on a dimmer, check the lamp is marked as suitable for dimming. 4. Look at the holder and the ceiling around it for scorching, discolouration or curled labels. 5. If the holder is damaged or marked by heat, do not fit another lamp. Leave the fitting off until it has been checked.

When should you call an electrician?

Call an electrician if the holder or ceiling shows heat marks, if bulbs fail in more than one fitting after you have matched the wattage and type, if the failures started after a dimmer or new fitting went in, or if downlights sit under loft insulation. Book the same day if you smell burning from a fitting.

What will the electrician actually do?

  • Isolate the circuit and inspect the lampholder, the fitting and the ceiling around it for heat damage
  • Check the marked lamp type and wattage against what is fitted, and fit the correct lamp
  • Check the dimmer is compatible with the lamps and replace it where it is not
  • Replace damaged holders or whole fittings, using fire-rated or insulation-contact types where downlights meet insulation
  • Test the circuit and connections where failures are not explained by the fitting

Who fixes this

What it usually costs

Lighting Installation Cost
£50–£200 per light fitting

Questions people ask

Why do my light bulbs keep blowing in one room?

Look first at the fittings in that room: a lamp above the marked maximum wattage, the wrong lamp type for a downlight, a non-dimmable LED on a dimmer, or a lampholder damaged by heat. If every fitting is correct and bulbs still fail, the room's circuit needs testing.

Can I put any LED bulb in a downlight?

No. Electrical Safety First says replacement lamps and components must be compatible with the fitting and its driver, and the stated rating must not be exceeded.

Can a dimmer switch make bulbs blow?

A lamp that is not suitable for dimming can fail early on a dimmer. Lamps that cannot be dimmed carry a marking to say so, so check the packaging before fitting one on a dimmer.

Is it safe to keep replacing the bulb?

Only while the holder is clean and undamaged. If it is scorched, corroded or discoloured, do not fit another lamp and get an electrician to look at it.

Sources & References

  1. Electrical Safety First: downlights
  2. Electrical Safety First: safe installation of retrofit LED lamps (Best Practice Guide 9)

Need an electrician?

Describe the job and get a fixed price from a local electrician.