Skip to main content
Loose Or Cracked Brick In A Wall

Loose Or Cracked Brick In A Wall

One brick has come loose, cracked or dropped out of a wall, and the question is whether it can be replaced on its own.

Caution · Fixed by a bricklayer

Updated

What's happening?

A single brick that moves, cracks or falls out is a local fault, but the cause behind it is not always local. A brick that has simply lost its mortar is the easy case: the joints around it have weathered or frozen and it can be bedded back. A brick that has cracked or split is usually frost or salt damage, a knock, or movement in the wall. A run of loose bricks near a corner, a window or a bulge suggests rusting wall ties or settlement, and that needs more than one brick put back. Replacing one brick means cutting out the failed brick and its mortar without disturbing the ones around it, matching the brick and the mortar mix, and pointing it so the repair sheds water. A wrong match shows, and a hard mortar can damage soft old bricks.

What usually causes it?

  • Mortar around the brick has weathered or frozen out, so the brick has lost its bed
  • Frost or salt damage has split or crumbled the brick itself
  • An impact from a vehicle, a ball or a ladder has cracked or dislodged it
  • Corroded wall ties allowing the outer leaf of a cavity wall to move
  • Movement or settlement in the wall, showing as loose bricks near a crack
  • A previous repair using a mortar harder than the surrounding brickwork

Is it dangerous?

A single brick falling is a small hazard but it can drop onto a path, a door or a person, and several loose bricks in one area can mean the wall is unstable. Keep clear of the area below a loose brick on an upper wall, and treat bricks loosening near a bulge or a crack as a structural question.

Can I fix it myself?

1. Look at the pattern: one brick, or several, or a bulge and cracks nearby. 2. If it is one brick at low level, you can bed it back with a mortar matched to the wall, but only after raking out the joints cleanly. 3. Do not use hard cement mortar on old, soft brickwork. 4. Do not climb ladders to work on a loose brick on an upper wall. 5. If the wall bulges or cracks around it, leave it and get it looked at.

When should you call a bricklayer?

Call a bricklayer for any loose brick above head height, for several loose bricks, or when the brick sits in a wall that is cracked, bulging or leaning. A bricklayer can match the brick and the mortar, and tell you whether it is a local repair or a symptom.

What will the bricklayer actually do?

  • Check the surrounding brickwork, ties and joints to see whether the loose brick is local or part of a wider fault
  • Cut out the failed brick and clean out the bed and perpends without damaging neighbours
  • Match the replacement brick for size, colour and texture, and the mortar for strength and mix
  • Bed and point the new brick so water sheds off the face
  • Recommend further repair, such as wall tie work or repointing, where the cause is wider

Who fixes this

  • Brickwork repair

Questions people ask

Can you replace a single brick in a wall?

Yes. The failed brick is cut out, the bed is cleaned, and a matching brick is bedded in and pointed. The match of brick and mortar determines how well it blends.

Why has a brick come loose in my wall?

Most often the mortar has weathered or frozen out. A split brick points to frost or salt damage, and several loose bricks near a crack or bulge can point to rusting wall ties or movement.

What mortar should be used to replace a brick?

One matched to the wall. SPAB advises that hard cement mortar can harm older bricks and stone, so the mortar should be no harder than the brickwork it is repairing.

Sources & References

  1. SPAB: Repointing
  2. GOV.UK: Structure, Approved Document A

Need a bricklayer?

Describe the job and get a fixed price from a local bricklayer.