Skip to main content
Gap Between the Bath and the Tiles

Gap Between the Bath and the Tiles

A gap that is too wide for sealant, or that reopens after resealing, means the bath is moving or was set away from the wall, and filling it only hides the cause.

Low risk · Fixed by a bathroom fitter

Updated

What's happening?

The seal between a bath and the wall tiles is a movement joint. A full bath is heavy, the bath flexes slightly under load and as it heats and cools, and the joint takes up that movement. Sealant makers publish how to design such a joint. Geocel's guide gives a joint at least 6mm wide, with the sealant between 6mm and 12mm deep and at least twice as wide as it is deep, and says a backer rod or bond breaker tape must be used if movement is anticipated. A wide gap breaks those rules: a thick bead of silicone sags and splits. A gap that opens again after resealing means the bath is still moving. Planning Portal notes a filled bath is heavy enough to overload a timber joist floor, which is one reason a bath sinks and pulls away.

What usually causes it?

  • A bath set too far from the wall at fitting, leaving a gap wider than a sealant joint is designed for
  • A bath that has moved or sunk as its feet or cradle settled or the floor beneath it gave
  • A timber joist and board floor flexing under the weight of a full bath
  • Sealant that was applied thicker than a joint should be and has sagged and split
  • Tiles that were fitted before the bath, so the final gap is whatever was left
  • Repeated movement as the bath fills, empties and heats, which opens a joint that was not formed with a backer rod

Is it dangerous?

The gap is not dangerous but it is a leak path: water that runs down the wall tiles gets behind the bath and under the floor, and can soften the floor and ceiling below. If the bath visibly moves when you stand in it, treat the gap as a symptom of a support problem and stop using the bath until it is checked.

Can I fix it myself?

1. Measure the gap with the bath empty and again with some water in it, to see whether it grows. 2. If it stays narrow and the bath does not move, cut out the old sealant, clean and dry the joint and reseal. 3. If the gap is wider than a normal sealant joint, do not fill it with a thick bead of silicone. 4. Check whether the bath rocks or sinks when someone sits in it. 5. If it moves, stop using it and get a bathroom fitter to look at the support and the floor.

When should you call a bathroom fitter?

Call a bathroom fitter if the gap is too wide for a sealant joint, if it reopens after resealing, if the bath moves under load, or if there is any stain on the ceiling below. A fitter can reset the bath or add a trim and seal correctly.

What will the bathroom fitter actually do?

  • Check the bath is level, supported and fixed, and reset it closer to the wall where possible
  • Check the floor under the bath for movement or damage, and strengthen it where a timber floor flexes
  • Cut out failed sealant and clean and dry the joint
  • Close a wide gap with a trim, backer rod or re-tiling so the sealant sits at the right width and depth
  • Seal the finished joint and check it again when the bath is full

Who fixes this

Questions people ask

How big a gap can silicone fill?

Sealant manufacturers design joints with a minimum width, a set depth range and a width-to-depth ratio. Geocel's guide gives sealant between 6mm and 12mm deep and at least twice as wide as deep. A big gap should be reduced or backed with a rod first.

Why does the sealant keep splitting at the bath?

The joint is moving, because a full bath is heavy and shifts, or the sealant bead is too thick. Resealing will not hold until the movement or the joint size is dealt with.

Can a bath sink into the floor?

Planning Portal says a new bathroom suite in a room with a timber joist and board floor risks overloading the floor from the bath once full of water, and that work to strengthen it may be necessary.

Can I fix a bath gap by tiling over it?

A tile edge or trim can cover a gap, but the bath should be level, supported and the final joint sealed with sealant, not grout, because the joint moves.

Sources & References

  1. Geocel: weathersealing manual
  2. Planning Portal: suitability of existing floor structures

Need a bathroom fitter?

Describe the job and get a fixed price from a local bathroom fitter.