Skip to main content
Spongy or Soft Bathroom Floor

Spongy or Soft Bathroom Floor

A bathroom floor that feels soft or springy usually has board or timber damaged by water, or a joist floor loaded beyond what it was built for, and it should be opened up and checked.

Caution · Fixed by a bathroom fitter

Updated

What's happening?

A floor that gives underfoot in a bathroom is telling you something about what is under the covering. Approved Document C says that in kitchens, utility rooms and bathrooms, where water may be spilled, any board used as flooring should be moisture resistant, and chipboard should be one of the grades with improved moisture resistance. Standard board that has been wetted by a leak, a failed seal or years of splashes loses strength and goes soft. Planning Portal adds a second possible cause: if a timber joist and board floor carries a bath that has been fitted or replaced, there is a significant risk of the floor being overloaded once the bath is full of water, and strengthening may be needed. A soft spot is rarely cosmetic.

What usually causes it?

  • Flooring board that is not moisture resistant, which Approved Document C says it should be in bathrooms
  • Water reaching the board through failed seals, grout, a leak or repeated splashing
  • A timber joist and board floor overloaded by the weight of a full bath
  • Chipboard flooring that is not one of the grades with improved moisture resistance
  • Boards or joists that have decayed after prolonged dampness
  • A floor covering laid over damaged board, which hides the soft area until it gives way

Is it dangerous?

A soft floor can fail suddenly. A person can put a foot through damaged board, and water that has softened the floor may also be reaching ceilings and wiring below. Keep weight off the soft area, keep the bath and shower out of use if the bath sits on it, and have it opened up quickly.

Can I fix it myself?

1. Press gently around the toilet, bath, shower and doorway to find the extent of the soft area. 2. Look for dampness, staining on the ceiling below and gaps in sealant or grout. 3. Fix an obvious leak or failed seal first. 4. Do not lay new flooring over a soft floor. 5. Get a bathroom fitter or carpenter to lift the covering and check the board and joists.

When should you call a bathroom fitter?

Call a bathroom fitter as soon as you find a soft area, particularly near the toilet, bath or shower, or where a new bath has gone in. They will find the cause, repair or replace the board and strengthen the joists where the floor is overloaded. If a leak is the cause, a plumber may be needed first.

What will the bathroom fitter actually do?

  • Lift the floor covering and inspect the board and joists for water damage and decay
  • Cut out and replace damaged boards with moisture-resistant board, laid and fixed as the manufacturer recommends
  • Repair or sister damaged joists, and add joists or support where a timber floor carries a bath
  • Seal the new floor and re-lay the covering with sealed joints
  • Check seals, tray and bath edges that let water through, and re-seal them

Who fixes this

Questions people ask

Why is my bathroom floor spongy?

The board under the covering has probably been wetted, or the floor is carrying more than it was built for. Approved Document C says boards used as flooring in bathrooms should be moisture resistant.

Can a heavy bath make the floor soft?

Planning Portal says a bath fitted on a timber joist and board floor risks overloading the floor once it is full of water, and that work to strengthen the floor may be needed. A structural engineer or surveyor can assess it.

What board should a bathroom floor have?

Approved Document C says any board used as flooring in kitchens, utility rooms and bathrooms should be moisture resistant, and chipboard should be one of the improved moisture resistance grades.

Can I just lay new flooring over it?

No. A soft area means the board or joists below are damaged or overloaded, so the covering should be lifted and the cause fixed first.

Sources & References

  1. GOV.UK: Approved Document C, site preparation and resistance to contaminants and moisture
  2. Planning Portal: suitability of existing floor structures

Need a bathroom fitter?

Describe the job and get a fixed price from a local bathroom fitter.