Skip to main content
Skim Coat Peeling Off the Wall

Skim Coat Peeling Off the Wall

A skim that peels in sheets has not bonded to its background, usually through a dusty, greasy, painted or over-absorbent surface that was not primed, and patching over it will not hold.

Low risk · Fixed by a plasterer

Updated

What's happening?

A finishing coat of plaster has to key into the surface behind it. When it lifts in sheets or peels away, the usual story is the bond failed. Bonding agent data sheets are explicit about what they need: Bostik says surfaces must be sound, dry, clean and free from grease, dust and loose material, and a PVA primer can improve adhesion to porous or difficult surfaces before plastering. SikaBond PVA+ is sold as a primer and sealer before plastering, painting or tiling, and notes it reduces surface porosity of plaster. Dulux adds that paint applied over a powdery or friable surface blisters and flakes. So the surface behind the skim is the first suspect: dust, grease, old paint, or a surface so absorbent it drew the water out of the plaster too fast.

What usually causes it?

  • A dusty, greasy or loose background that the plaster could not key into
  • A very absorbent or difficult surface that was not primed, so the skim dried too fast to bond
  • Old paint or a powdery, friable surface behind the skim that gives way underneath it
  • Plaster applied over a surface that was not sound, dry or clean
  • Painting before the skim has dried, trapping moisture under the paint film
  • Movement in the wall or ceiling behind the skim that breaks the bond

Is it dangerous?

A peeling skim is not dangerous on a wall. On a ceiling, loose plaster can fall, so treat any hollow-sounding or sagging patch as something to bring down safely. Wear a dust mask when scraping and sanding.

Can I fix it myself?

1. Tap the wall or ceiling around the failure and mark every area that sounds hollow. 2. Scrape off loose skim back to firm plaster, wearing a dust mask and protecting the floor. 3. Do not skim over loose paint or dust: remove loose material and wipe the surface clean. 4. Prime the surface with a bonding agent suited to the background, following the data sheet's dilution and drying instructions. 5. If more than a small area is failing, or it is on a ceiling, get a plasterer rather than patching.

When should you call a plasterer?

Call a plasterer if more than a small area is lifting, if the failure is on a ceiling, if the skim has failed twice, or if the plaster sounds hollow beyond the visible patch. A plasterer will decide whether to cut out and re-skim or strip the whole wall.

What will the plasterer actually do?

  • Tap the whole wall or ceiling to find every area that has lost its bond, not only the visible failure
  • Strip the failed skim back to a sound, clean, dust-free surface
  • Prime the background with a bonding agent suited to its absorbency, and let it reach the right state before plastering
  • Re-skim to a level finish and allow it to dry before decorating
  • Advise whether the wall needs dry-lining or plasterboard rather than another skim over a poor background

Who fixes this

  • Skimming and re-skimming
  • Wall and ceiling repairs

Questions people ask

Why is my skim coat peeling off?

The skim has not bonded to its background. Bonding agent makers say the surface must be sound, dry, clean and free from grease, dust and loose material, and porous or difficult surfaces need priming.

Can I skim over painted walls?

Paint over a powdery or friable surface blisters and flakes, per Dulux, so loose paint needs removing first. A plasterer will choose the bonding agent that suits the surface.

What does PVA do under plaster?

SikaBond PVA+ data states it is a primer and sealer before plastering and reduces the surface porosity of plaster. Bostik says PVA primes porous or difficult surfaces prior to plastering.

How long before I can paint new plaster?

Dulux says new plaster should dry for at least one to two weeks before its damp seal primer is used. Paint on damp plaster traps moisture and can blister.

Sources & References

  1. Bostik: PVA building adhesive, primer and sealer data sheet
  2. SikaBond PVA+ product data sheet
  3. Dulux: 15 paint problems and how to fix them

Need a plasterer?

Describe the job and get a fixed price from a local plasterer.